Docol® 800CP complex phase
More about complex phase steelDownload data sheet
Product & services
Brands & products
Docol
All automotive steel grades
Complex phase steel
Docol® 800CP complex phase automotive steel
/ ...
/
Complex phase steel
/
Docol® 800CP complex phase automotive steel
Docol® 800CP complex phase automotive steel
Current page
On this page
General Product Description
Docol 800CP is intended for designs where high structural strength and energy absorption are desired, suitable for cold formed safety components and crash-relevant equipment within the automotive and transport industries.
Dimension Range
Cold rolled / UC: thickness 0.50-2.10 mm, width up to 1527 mm.
Cold rolled / GI, GA, ZA: thickness 0.80-2.50 mm, width up to 1460 mm.
Hot rolled / UC: thickness 2.00-4.00 mm, width up to 1500 mm.
Hot rolled / GI: thickness 2.00-3.50 mm, width up to 1400 mm.
Slit strip and cut to length sheets are available upon request.
Grade and coating specific restrictions on available dimensions may occur.
Mechanical Properties
Hide/Show specific columns Edit
Select columns to display
| Standard | Coating | Test direction |
Yield strength Rp0.2 (MPa) |
Tensile strength Rm (MPa) |
Elongation A80 (min %) |
Elongation A5 (min %) |
BH2 (min MPa) |
Hole expansion ratio 2)(min %) | Hole expansion ratio 2) (% typical) |
|
|---|---|---|---|---|---|---|---|---|---|---|
| Docol CR570Y780T-CP | VDA 239-100 | UC, GI, GA*, ZA* | L | 570 - 720 | 780 - 920 | 10 1) | — | 30 | — | — |
| Docol HR660Y760T-CP | VDA 239-100 | UC, GI | L | 660 - 820 | 760 - 960 | 10 | 13 | 30 | — | — |
| Docol HR800HER-75 | SSAB | UC, GI | L | 660 - 820 | 760 - 960 | 11 | 14 | 30 | 45 | 75 |
| Docol HR800HER-100 | SSAB | UC | L | 660 - 820 | 760 - 960 | 12 | 15 | 30 | 65 | 100 |
| Docol Roll 800 | SSAB | UC | T | 600 - 750 | 800 - 950 | 10 | — | — | — | — |
Compare parameters
Select one parameter to compare
Comparison
Docol CR570Y780T-CP
Standard
VDA 239-100
Coating
UC, GI, GA*, ZA*
Test direction
L
Yield strength Rp0.2
(MPa)
(MPa)
570 - 720
Tensile strength Rm
(MPa)
(MPa)
780 - 920
Elongation A80
(min %)
(min %)
10 1)
Elongation A5
(min %)
(min %)
—
BH2
(min MPa)
(min MPa)
30
Hole expansion ratio 2)(min %)
—
Hole expansion ratio 2)
(% typical)
(% typical)
—
Expand
Collapse
Docol HR660Y760T-CP
Standard
VDA 239-100
Coating
UC, GI
Test direction
L
Yield strength Rp0.2
(MPa)
(MPa)
660 - 820
Tensile strength Rm
(MPa)
(MPa)
760 - 960
Elongation A80
(min %)
(min %)
10
Elongation A5
(min %)
(min %)
13
BH2
(min MPa)
(min MPa)
30
Hole expansion ratio 2)(min %)
—
Hole expansion ratio 2)
(% typical)
(% typical)
—
Expand
Collapse
Docol HR800HER-75
Standard
SSAB
Coating
UC, GI
Test direction
L
Yield strength Rp0.2
(MPa)
(MPa)
660 - 820
Tensile strength Rm
(MPa)
(MPa)
760 - 960
Elongation A80
(min %)
(min %)
11
Elongation A5
(min %)
(min %)
14
BH2
(min MPa)
(min MPa)
30
Hole expansion ratio 2)(min %)
45
Hole expansion ratio 2)
(% typical)
(% typical)
75
Expand
Collapse
Docol HR800HER-100
Standard
SSAB
Coating
UC
Test direction
L
Yield strength Rp0.2
(MPa)
(MPa)
660 - 820
Tensile strength Rm
(MPa)
(MPa)
760 - 960
Elongation A80
(min %)
(min %)
12
Elongation A5
(min %)
(min %)
15
BH2
(min MPa)
(min MPa)
30
Hole expansion ratio 2)(min %)
65
Hole expansion ratio 2)
(% typical)
(% typical)
100
Expand
Collapse
Docol Roll 800
Standard
SSAB
Coating
UC
Test direction
T
Yield strength Rp0.2
(MPa)
(MPa)
600 - 750
Tensile strength Rm
(MPa)
(MPa)
800 - 950
Elongation A80
(min %)
(min %)
10
Elongation A5
(min %)
(min %)
—
BH2
(min MPa)
(min MPa)
—
Hole expansion ratio 2)(min %)
—
Hole expansion ratio 2)
(% typical)
(% typical)
—
Expand
Collapse
*Available upon request.
1) For GA coatings the minimum elongation value is reduced by 2 units.
2) HER –ratio is average of three test results out of five tested samples by excluding minimum and maximum results.
Chemical Composition (ladle analysis)
Hide/Show specific columns Edit
Select columns to display
| Coating | C (max %) |
Si (max %) |
Mn (max %) |
P (max %) |
S (max %) |
Al (%) |
Nb+Ti (max %) |
Cr+Mo (max %) |
B (max %) |
Cu (max %) |
|
|---|---|---|---|---|---|---|---|---|---|---|---|
| Docol CR570Y780T-CP | UC, GI, GA*, ZA* | 0.18 | 1.00 | 2.50 | 0.050 | 0.010 | 0.015 - 1.00 | 0.15 | 1.00 | 0.005 | 0.20 |
| Docol HR660Y760T-CP | UC, GI | 0.18 | 1.00 | 2.20 | 0.050 | 0.010 | 0.015 - 1.2 | 0.25 | 1.00 | 0.005 | 0.20 |
| Docol HR800HER-75 | UC, GI | 0.18 | 1.00 | 2.20 | 0.050 | 0.010 | 0.015 - 1.2 | 0.25 | 1.00 | 0.005 | 0.20 |
| Docol HR800HER-100 | UC | 0.18 | 1.00 | 2.20 | 0.050 | 0.010 | 0.015 - 1.2 | 0.25 | 1.00 | 0.005 | 0.20 |
| Docol Roll 800 | UC | 0.16 | 0.40 | 1.80 | 0.020 | 0.010 | From 0.015 | 0.10 | — | — | — |
Compare parameters
Select one parameter to compare
Comparison
Docol CR570Y780T-CP
Coating
UC, GI, GA*, ZA*
C
(max %)
(max %)
0.18
Si
(max %)
(max %)
1.00
Mn
(max %)
(max %)
2.50
P
(max %)
(max %)
0.050
S
(max %)
(max %)
0.010
Al
(%)
(%)
0.015 - 1.00
Nb+Ti
(max %)
(max %)
0.15
Cr+Mo
(max %)
(max %)
1.00
B
(max %)
(max %)
0.005
Cu
(max %)
(max %)
0.20
Expand
Collapse
Docol HR660Y760T-CP
Coating
UC, GI
C
(max %)
(max %)
0.18
Si
(max %)
(max %)
1.00
Mn
(max %)
(max %)
2.20
P
(max %)
(max %)
0.050
S
(max %)
(max %)
0.010
Al
(%)
(%)
0.015 - 1.2
Nb+Ti
(max %)
(max %)
0.25
Cr+Mo
(max %)
(max %)
1.00
B
(max %)
(max %)
0.005
Cu
(max %)
(max %)
0.20
Expand
Collapse
Docol HR800HER-75
Coating
UC, GI
C
(max %)
(max %)
0.18
Si
(max %)
(max %)
1.00
Mn
(max %)
(max %)
2.20
P
(max %)
(max %)
0.050
S
(max %)
(max %)
0.010
Al
(%)
(%)
0.015 - 1.2
Nb+Ti
(max %)
(max %)
0.25
Cr+Mo
(max %)
(max %)
1.00
B
(max %)
(max %)
0.005
Cu
(max %)
(max %)
0.20
Expand
Collapse
Docol HR800HER-100
Coating
UC
C
(max %)
(max %)
0.18
Si
(max %)
(max %)
1.00
Mn
(max %)
(max %)
2.20
P
(max %)
(max %)
0.050
S
(max %)
(max %)
0.010
Al
(%)
(%)
0.015 - 1.2
Nb+Ti
(max %)
(max %)
0.25
Cr+Mo
(max %)
(max %)
1.00
B
(max %)
(max %)
0.005
Cu
(max %)
(max %)
0.20
Expand
Collapse
Docol Roll 800
Coating
UC
C
(max %)
(max %)
0.16
Si
(max %)
(max %)
0.40
Mn
(max %)
(max %)
1.80
P
(max %)
(max %)
0.020
S
(max %)
(max %)
0.010
Al
(%)
(%)
From 0.015
Nb+Ti
(max %)
(max %)
0.10
Cr+Mo
(max %)
(max %)
—
B
(max %)
(max %)
—
Cu
(max %)
(max %)
—
Expand
Collapse
* Available upon request.
Tolerances
Cold rolled (UC): Tolerances in accordance to EN 10131.
Hot rolled (UC): Tolerances in accordance to EN 10051.
Hot-dip galvanized (GI, GA, ZA): Tolerances in accordance to EN 10143.
Customized dimensional and shape tolerances are available upon request.
Coatings
The metal coating options for Docol products include:
Hot-dip zinc coating (GI) consists almost entirely of zinc (>99%). It is lead free, resulting in a small zinc spangle size. The coating provides good corrosion protection.
Galvannealed coating (GA) is a zinc-iron alloy coating having an iron content of approximately 10%. Galvannealed is produced by post-heat treatment in continuous hot-dip coating process. Galvannealed provides excellent resistance weldability and corrosion protection of painted products.
Galfan coating (ZA) is a zinc-aluminium alloy coating having the eutectic composition approximately of 95% Zn and 5% Al. Galfan is produced in continuous hot-dip coating process. Galfan has better anticorrosive and forming properties than conventional hot-dip zinc coating (GI).
Electrogalvanized coating (EG) is applied continuously by electro deposition. The coating consists of zinc (>99%). Electrogalvanized steel is characterized by its excellent surface quality and uniform coating thickness.
Grade specific availability of metal coatings for Docol products is given in the Mechanical properties table (Coating).
Hide/Show specific columns Edit
Select columns to display
| Coating type | Coating class | Standard | Closest in EN 10346, informative | Coating mass per side, single spot test (g/m2) | Thickness per side informative (µm) |
|---|---|---|---|---|---|
| GI | 40/40 | VDA 239-100 | Z100 | 40 - 60 1) | 5.6 - 8.5 |
| GI | 50/50 | VDA 239-100 | — | 50 - 70 1) | 7.0 - 9.9 |
| GI | 60/60 | VDA 239-100 | Z140 | 60 - 90 | 8.5 - 12.7 |
| GI | 70/70 | VDA 239-100 | — | 70 - 100 | 9.9 - 14.1 |
| GI | 85/85 | VDA 239-100 | — | 85 - 115 | 12.0 - 16.2 |
| GI | 115/115 | VDA 239-100 | Z275 | 115 - 155 | 16.2 - 21.8 |
| GA | 40/40 | VDA 239-100 | ZF100 | 40 - 60 1) | 5.6 - 8.5 |
| GA | 50/50 | VDA 239-100 | ZF120 | 50 - 80 | 7.0 - 11.3 |
| ZA | 95 | EN 10346 | ZA95 | — | 7.0 - |
| ZA | 130 | EN 10346 | ZA130 | — | 10.0 - |
| EG | 25/25 | EN 10152 | — | 12 - | 1.7 - |
| EG | 50/50 | EN 10152 | — | 29 - | 4.1 - |
| EG | 75/75 | EN 10152 | — | 47 - | 6.6 - |
| EG | 100/100 | EN 10152 | — | 65 - | 9.1 - |
Compare parameters
Select one parameter to compare
Comparison
Coating type
GI
Coating class
40/40
Standard
VDA 239-100
Closest in EN 10346, informative
Z100
Coating mass per side, single spot test (g/m2)
40 - 60 1)
Thickness per side informative (µm)
5.6 - 8.5
Expand
Collapse
Coating type
GI
Coating class
50/50
Standard
VDA 239-100
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
50 - 70 1)
Thickness per side informative (µm)
7.0 - 9.9
Expand
Collapse
Coating type
GI
Coating class
60/60
Standard
VDA 239-100
Closest in EN 10346, informative
Z140
Coating mass per side, single spot test (g/m2)
60 - 90
Thickness per side informative (µm)
8.5 - 12.7
Expand
Collapse
Coating type
GI
Coating class
70/70
Standard
VDA 239-100
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
70 - 100
Thickness per side informative (µm)
9.9 - 14.1
Expand
Collapse
Coating type
GI
Coating class
85/85
Standard
VDA 239-100
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
85 - 115
Thickness per side informative (µm)
12.0 - 16.2
Expand
Collapse
Coating type
GI
Coating class
115/115
Standard
VDA 239-100
Closest in EN 10346, informative
Z275
Coating mass per side, single spot test (g/m2)
115 - 155
Thickness per side informative (µm)
16.2 - 21.8
Expand
Collapse
Coating type
GA
Coating class
40/40
Standard
VDA 239-100
Closest in EN 10346, informative
ZF100
Coating mass per side, single spot test (g/m2)
40 - 60 1)
Thickness per side informative (µm)
5.6 - 8.5
Expand
Collapse
Coating type
GA
Coating class
50/50
Standard
VDA 239-100
Closest in EN 10346, informative
ZF120
Coating mass per side, single spot test (g/m2)
50 - 80
Thickness per side informative (µm)
7.0 - 11.3
Expand
Collapse
Coating type
ZA
Coating class
95
Standard
EN 10346
Closest in EN 10346, informative
ZA95
Coating mass per side, single spot test (g/m2)
—
Thickness per side informative (µm)
7.0 -
Expand
Collapse
Coating type
ZA
Coating class
130
Standard
EN 10346
Closest in EN 10346, informative
ZA130
Coating mass per side, single spot test (g/m2)
—
Thickness per side informative (µm)
10.0 -
Expand
Collapse
Coating type
EG
Coating class
25/25
Standard
EN 10152
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
12 -
Thickness per side informative (µm)
1.7 -
Expand
Collapse
Coating type
EG
Coating class
50/50
Standard
EN 10152
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
29 -
Thickness per side informative (µm)
4.1 -
Expand
Collapse
Coating type
EG
Coating class
75/75
Standard
EN 10152
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
47 -
Thickness per side informative (µm)
6.6 -
Expand
Collapse
Coating type
EG
Coating class
100/100
Standard
EN 10152
Closest in EN 10346, informative
—
Coating mass per side, single spot test (g/m2)
65 -
Thickness per side informative (µm)
9.1 -
Expand
Collapse
Docol metal coated products are available with surface quality for unexposed applications.
In addition to these coating masses, OEM specific coatings and single sided EG coatings are available upon request.
1) For hot-dipped (GI, ZA, GA) hot rolled (HR) grades, the coating mass tolerance is increased to 30 g/m² by increasing the upper limit.
Surface Treatments
Uncoated (UC): available as oiled.
Hot-dip galvanized (GI, GA, ZA): available as oiled and/or chemically passivated.
Electrogalvanized (EG): available as oiled and/or chemically passivated or phosphated.
All surface treatments are in accordance with RoHS directive (2011/65/EU) and do not contain Chromium VI (Cr6+). Surface treatments provide only temporary surface protection during transportation and storage. In order to avoid corrosion damages, care must be taken to keep the products dry during transportation and storage. If they become wet, they must be separated and situated so that they are dried quickly.
Fabrication and Other Recommendations
For information concerning fabrication, see SSAB´s brochures on www.ssab.com or consult Tech Support.
Appropriate health and safety precautions must be taken when bending, welding, cutting, grinding or otherwise working on the products.
Docol® Complex Phase steel product offer
Docol® 600 CP complex phase
Docol® 800CP complex phase
Docol® 1000CP complex phase
Docol® 1200CP complex phase
Related content
-
AHSS trial material stock
Want to discover unique automotive applications for AHSS materials? Try new production methods? Or create lighter components that can improve fuel efficiency, crash-worthiness and sustainability?
-
Recommended AHSS steels for car applications
Docol® steel grades serve specific design purposes and are chosen by designers for a wide range of applications and used by OEMs and tier suppliers in millions of vehicles around the world.
-
Forming data for Docol® AHSS steels
Existing Docol® customers get 24/7 access to the forming data you need to help in your selection and simulation of automotive advanced high strength steels.